background image

PART Ⅰ  FOR SAFE WORK

A. WARNING! Pay attention to safety.
B. WARNING! Read the operation manual carefully.
C. DANGER! When carrying out service, stop the engine and remove engine key.
D. DANGER! When the engine is running, do not look into auger. Keep hands and feet away from auger.
   Failure to comply may result in getting caught in the machine and death.
E. DANGER! When removing snow from auger, be sure to stop the engine, and use installed unclogging stick.
   Failure to comply may result in getting caught in the machine and death.
F. DANGER! Be sure to attach the covers to correct positions. Using the machine without covers may
   result in injury.
G. DANGER! When the engine is running, do not look into chute. Keep hands away from chute.  When 
   removing snow from chute, be sure to stop the engine, and use installed unclogging stick. Failure to 
   comply may result in getting caught in the machine and injury.
H. WARNING! Do not turn chute toward people and buildings during work. Scattered objects may cause
    injury and damage.
I.  DANGER! Keep people away from the machine during work.
J. WARNING!  Be careful of exhaust fumes. Exhaust fumes contain poisonous gas which may cause death.
K. DANGER! Start moving the machine slowly. Before starting, be sure to check the safety in traveling 
    direction, and then, set travel clutch at "On" position. Failure to comply may result in death.
L. DANGER! Do not stop the machine on slope. Do not set change lever at "Neutral" position 
   on slope or when loading/unloading the machine on a truck.  The machine may slip down, 
   and injury may occur.

SH3-01 

A            B             C 

G            H             I 

A          B           C 

D           E           F 

 

 
 

 
 

 
 

 

 
 

 
 

 
 

8600-13-73-0 
MARK/CAUTION B/ISO 

8600-13-72-0 
MARK/CAUTION A/ISO 

8600-13-74-0                    
MARK/CAUTION C/ISO 

- 16 -

Содержание 913ML2-S







































































Отзывы: