FUJII 913ML2-S Скачать руководство пользователя

Страница: 49 / 70

PART Ⅱ OPERATION SNOWMATIC plus

■MODE 1 (optional angle control : up/down, right/left)

　●

Mode 1 sets up an optional angle (up/down and right/left) for automatic control according to
work conditions. It automatically keeps auger housing at the angle.

(1)

Operate auger housing control lever and adjust auger
housing to the angle (up/down, right/left) which you
want to set up.

(2)

Turn the knob of mode change switch and choose
"Mode 1".

(3)

Press Snowmatic plus button. Light inside the

button is turned on. When pressing the button, the

angle of auger housing is set up for automatic

control. Automatic control of Mode 1 is activated.

●

The angle (up/down and right/left) which

is set up in Mode 1 will be deleted when
Snowmatic plus is turned off.

●

Even if the order of procedures (1) and (2) are reversed, it will

function normally.

■MODE 2 (horizontal control : up/down, right/left)

　●

Mode 2 automatically keeps auger housing horizontal (up/down and right/left).

(1)

Turn the knob of mode change switch and choose
"Mode 2".

(2)

Press Snowmatic plus button. Light inside the button

is turned on. Automatic control of Mode 2 is activated.

Optional angle control (up and down)

Horizontal control (up and down)

Horizontal control (right and left)

Optional angle control (right and left)

Up/down

１

２

３

Snowmatic
plus button

Mode change switch

Knob

１

２

３

SH3-07

SH3-08

SH3-09

SH3-10

Snowmatic
plus button

Mode change switch

Knob

SUPPLEMENT

- 44 -

Содержание 913ML2-S







































































Результаты поиска

Содержание 913ML2-S

Отзывы:

Похожие инструкции для 913ML2-S

Бренды по названию

Популярные бренды

FUJII 913ML2-S, Руководство по эксплуатации

Результаты поиска

Содержание 913ML2-S

Отзывы:

Похожие инструкции для 913ML2-S

Бренды по названию

Популярные бренды