FUJII 913ML2-S Скачать руководство пользователя

Страница: 9 / 70

PART Ⅰ FOR SAFE WORK

WARNING Fire is strictly prohibited when inspecting battery.

Fire is strictly prohibited when inspecting
the battery or opening the vent plug.

[Results of failure to comply]
Failure to comply may result in fire caused by
ignition of gas from battery.

DANGER Do not get under the machine nor place your feet under the machine.

Do not get under the machine nor place your feet
under the machine.

[Results of failure to comply]
Failure to comply may result in injury if the machine
moves for some reason.

WARNING Be cautious of exhaust gas.

Do not start the engine indoors, except when moving
the machine from inside the building. Ensure sufficient
ventilation even when moving the machine.

[Results of failure to comply]
Failure to comply may cause exhaust gas poisoning
or even death.

DANGER Be cautious of fuel leakage.

If the fuel pipe is broken, it may cause fuel leakage.
Be sure to inspect it before work.

[Results of failure to comply]
Failure to comply may result in fire caused by ignition
of fuel.

DANGER Shut fuel cap and wipe off any spilled fuel.

After adding fuel, be sure to shut the fuel cap securely
and wipe off any spilled fuel.

[Results of failure to comply]
Failure to comply may result in fire caused by ignition of fuel.

Harmful gas

- 4 -

Содержание 913ML2-S







































































Результаты поиска

Содержание 913ML2-S

Отзывы:

Похожие инструкции для 913ML2-S

Бренды по названию

Популярные бренды

FUJII 913ML2-S, Руководство по эксплуатации

Результаты поиска

Содержание 913ML2-S

Отзывы:

Похожие инструкции для 913ML2-S

Бренды по названию

Популярные бренды