manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Справочное руководство

Продукт Freescale Semiconductor Symphony DSP56724 - это высокотехнологичный микроконтроллер с цифровым сигнальным процессором. Если вам нужна более подробная информация о его функциях и возможностях, вы можете бесплатно скачать Руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

1-4

Freescale Semiconductor

 

Introduction

1.3

Features

In addition to high MIPS, the DSP56724/DSP56725 provides powerful and flexible audio data 
communications and supports a wide variety of audio applications. This section provides a brief 
description of the DSP56724/DSP56725 processor features.

The DSP56724/DSP56725 has two DSP56300 DSP cores. The high throughput of the DSP56300 family 
of processors makes them well-suited for high-speed control, efficient signal processing, numeric 
processing, and audio applications. Benefits of using DSP56300 cores include:

•

Speed: The DSP56300 family supports most high-performance DSP applications.

•

Precision: The data paths are 24 bits wide, providing 144 dB of dynamic range. Intermediate 
results held in the 56-bit accumulators can range over 336 dB.

•

Parallelism: Each on-chip execution unit, memory, and peripheral operates independently and in 
parallel with the other units through a sophisticated bus system. The Data ALU, AGU, and program 
controller operate in parallel so that the following operations can execute in a single instruction:

— An instruction pre-fetch

— A 24-bit

 × 

24-bit multiplication

— A 54-bit addition

— Two data moves

— Two address-pointer updates using either linear or modulo arithmetic

•

Flexibility: While many other DSPs require external communication devices to interface with 
peripheral circuits (such as A/D converters, D/A converters, or processors), the DSP56300 family 
provides on-chip serial and parallel interfaces that support various configurations of memory and 
peripheral modules. The peripherals are interfaced to the DSP56300 family core through a 
peripheral interface bus that provides a common interface to many different peripherals.

•

Sophisticated Debugging: Freescale’s On-Chip Emulation (OnCE) technology allows simple, 
inexpensive, and speed-independent access to the internal registers for debugging. With the OnCE 
module, you can easily determine the exact status of the registers and memory locations, plus 
identify which instructions were executed last.

•

Phase Locked Loop (PLL)-Based Clocking: The PLL allows the chip to use almost any available 
external system clock for full-speed operation, while also supplying an output clock synchronized 
to a synthesized internal core clock. It improves the synchronous timing of the external memory 
port, eliminating the timing skew common on other processors. 

•

Invisible Pipeline: The seven-stage instruction pipeline is essentially invisible to the programmer, 
allowing straightforward program development in either assembly language or high-level 
languages such as C or C++.

•

Similar Instruction Set: The instruction mnemonics are similar to those used for microcontroller 
units, making an easy transition from programming microprocessors to programming the device. 
New microcontroller instructions, addressing modes, and bit field instructions allow for significant 
decreases in program code size. The orthogonal syntax controls the parallel execution units. The 
hardware DO loop and the repeat (REP) instructions make writing straight-line code obsolete. 

•

Low Power: Designed in CMOS, the DSP56300 family consumes very little power. Two additional 
low-power modes, Stop and Wait, further reduce power requirements. Wait is a low-power mode 

Содержание Symphony DSP56724





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Symphony DSP56724

Xpand XPAND 3D User Manual preview
XPAND 3D
Бренд: Xpand Страницы: 24
Domo PIET HUYSENTRUYT DO9076KR Instruction Booklet preview
PIET HUYSENTRUYT DO9076KR
Бренд: Domo Страницы: 62
Black & Decker HandyChopper HC2000 Use And Care Book Manual preview
HandyChopper HC2000
Бренд: Black & Decker Страницы: 6
Myria MY4069 Instruction Manual preview
MY4069
Бренд: Myria Страницы: 15
Fagor RT-507 Instructions For Use Manual preview
RT-507
Бренд: Fagor Страницы: 48
Waring FPC14 Instruction Manual preview
FPC14
Бренд: Waring Страницы: 8
Lindy 32698 User Manual preview
32698
Бренд: Lindy Страницы: 31
DAS AUDIO INTEGRAL-VC1 User Manual preview
INTEGRAL-VC1
Бренд: DAS AUDIO Страницы: 10
Assistent ORIGINAL ANKARSRUM N30 User Manual preview
ANKARSRUM N30
Бренд: Assistent ORIGINAL Страницы: 25
Qomo WIPS2 User Manual preview
WIPS2
Бренд: Qomo Страницы: 62
Ultimate Chopper Food Chopper Instruction Manual preview
Food Chopper
Бренд: Ultimate Chopper Страницы: 4
Waring WFP16SE Instructions Manual preview
WFP16SE
Бренд: Waring Страницы: 152
TC Electronic DBMAX-V 2.90 User Manual preview
DBMAX-V 2.90
Бренд: TC Electronic Страницы: 61
VocoPro DA-8808VE Owner'S Manual preview
DA-8808VE
Бренд: VocoPro Страницы: 18
Brateck EPB-1 Installation Instructions Manual preview
EPB-1
Бренд: Brateck Страницы: 6
Eco-De Dieta Chef User Manual preview
Dieta Chef
Бренд: Eco-De Страницы: 44
NEC NC1100CM Installation Manual preview
NC1100CM
Бренд: NEC Страницы: 12
Epson PowerLite 8000i Specifications preview
PowerLite 8000i
Бренд: Epson Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды