Freescale Semiconductor Symphony DSP56724 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 436

background image

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

8-10

Freescale Semiconductor

General Purpose Input/Output (GPIO)

8.2.5.1

Port G Control Registers (PCRG, PCRG1)

The read/write 24-bit Port G Control Registers (PCRG, PCRG1) and the Port G Direction Registers
(PRRG, PRRG1) together control the functionality of the Port G GPIO pins. Each of the PG[39:0] bits
controls the functionality of the corresponding port pin. For the port-pin configuration, see

External Interrupt pins and the PLL lock output will act as non-GPIO functions after reset; so
corresponding bits of PRRG and PCRG will be set to “1” after reset.

8.2.5.2

Port G Direction Register (PRRG, PRRG1)

The read/write 24-bit Port G Direction Registers (PRRG, PRRG1) and the Port G Control Register (PCRG,
PCRG1) together control the functionality of the dedicated GPIO pins. For the port-pin configuration, see

External Interrupt pins and the PLL lock output will act as non-GPIO functions after reset; so
corresponding bits of PRRG and PCRG will be set to “1” after reset.

8.2.5.3

Port G Data Register (PDRG, PDRG1)

The read/write 24-bit Port G Data Registers (PDRG, PDRG1) are used to read/write data from/to the
dedicated GPIO pins. Bits PD[39:0] are used to read/write data from/to the corresponding port pins if they
are configured as GPIO.

•

If a port pin [i] is configured as a GPIO input, then the corresponding PD[i] bit reflects the value
present on this pin.

•

If a port pin [i] is configured as a GPIO output, then the value written into the corresponding PD[i]
bit is reflected on this pin.

•

If a port pin [i] is configured as disconnected, then the corresponding PD[i] bit does not reflect the
value present on this pin.

8.2.6

Timer Event Counter Signals

There are two identical Timer Event Counter (TEC) blocks (TEC, TEC_1), one timer block for each DSP
core. When not used as timer signals, the two sets of timer event counter signals (TIO0, TIO1, TIO2,
TIO0_1, TIO1_1, TIO2_1) can be configured as GPIO signals. The timer event counter signals are
controlled by the appropriate timer control status register (TCSR), which is described in

“Triple Timer Module (TEC, TEC_1)

.”

Table 8-11. PCRG and PRRG Bits Functionality

PDG[i]

PG[i]

Port Pin[i] Function

0

0

Disconnected

0

1

GPIO input

1

0

GPIO output

1

1

S/PDIF,... function

«
...
120
121
122
123
124
...
»

Содержание Symphony DSP56724





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Symphony DSP56724

Бренд: TZS First AUSTRIA Страницы: 18

Бренд: Crestron Страницы: 96

Бренд: KitchenAid Страницы: 52

Essential MC-400S

Бренд: Wilfa Страницы: 54

Бренд: OSKAR Страницы: 24

Бренд: Fritel Страницы: 16

Бренд: BSS Audio Страницы: 7

Бренд: Hamilton Beach Страницы: 20

Бренд: HELIX Страницы: 37

Бренд: Elmo Страницы: 82

Бренд: Pyle Страницы: 1

SYSTEM V BT5890-010

Бренд: B-Tech Страницы: 12

Бренд: Audiotec Fischer Страницы: 20

Бренд: Moulinex Страницы: 6

Бренд: Moulinex Страницы: 30

Бренд: NASA electric Страницы: 21

Бренд: Zephir Страницы: 6

Stack & Snap 70822

Бренд: Hamilton Beach Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды