manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVM series, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor MC9S12ZVM series Скачать руководство пользователя страница 219

Chapter 6 S12Z Debug (S12ZDBGV2) Module

MC9S12ZVM Family Reference Manual Rev. 1.3

Freescale Semiconductor

219

6.4.5.2.2

Loop1 Mode

Loop1 Mode, similarly to Normal Mode also stores only COF address information to the trace buffer, it
however allows the filtering out of redundant information.

The intent of Loop1 Mode is to prevent the trace buffer from being filled entirely with duplicate
information from a looping construct such as delays using the DBNE instruction. The DBG monitors trace
buffer entries and prevents consecutive duplicate address entries resulting from repeated branches.

Loop1 Mode only inhibits consecutive duplicate source address entries that would typically be stored in
most tight looping constructs. It does not inhibit repeated entries of destination addresses or vector
addresses, since repeated entries of these could indicate a bug in application code that the DBG module is
designed to help find.

The trace buffer format for Loop1 Mode is the same as that of Normal Mode.

6.4.5.2.3

Detail Mode

When tracing CPU activity in Detail Mode, address and data of data and vector accesses are traced. The
information byte indicates the size of access and the type of access (read or write).

ADRH, ADRM, ADRL denote address high, middle and low byte respectively. The numerical suffix
indicates which tracing step. DBGCNT increments by 2 for each line completed.

If timestamps are enabled then each CPU entry can span 2 trace buffer lines, whereby the second line
includes the timestamp. If a valid PC occurs in the same cycle as the timestamp, it is also stored to the trace
buffer and the PC bit is set. The second line featuring the timestamp is only stored if no further data access
occurs in the following cycle. This is shown in

Table 6-52

, where data accesses 2 and 3 occur in

consecutive cycles, suppressing the entry2 timestamp. If 2 lines are used for an entry, then DBGCNT
increments by 4. A timestamp line is indicated by bit1 in the TSINF byte. The timestamp counter is only
reset each time a timestamp line entry is made. It is not reset when the data and address trace buffer line
entry is made.

10

Source address of COF opcode

11

Destination address of COF opcode

Table 6-51. Detail Mode Trace Buffer Format without Timestamp

Mode

8-Byte Wide Trace Buffer Line

7

6

5

4

3

2

1

0

CPU

Detail

CDATA31

CDATA21

CDATA11

CDATA01

CINF1

CADRH1

CADRM1

CADRL1

CDATA32

CDATA22

CDATA12

CDATA02

CINF2

CADRH2

CADRM2

CADRL2

Table 6-50. CET Encoding

CET

Entry Type Description

Содержание MC9S12ZVM series


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды