42
ENGLISH
SECTION 3
Transport
3.1 TRANSPORT
In case it is necessary to transport the machine on a
long route, this may be loaded onto trucks or other
suitable means of transport.
In order to load the machine onto the means of trans-
port, it is necessary to have two special loading ramps.
These ramps shall have a capacity of at least Kg. 300
each, a width of at least cm 30, the edges about cm 5
high and such a length so that the inclination does
not exceed the 15
°
/20
°
with respect to the horizon
line; they must be also equipped with a hooking sys-
tem to the means of transport.
WARNING
The loading operations may be very dangerous if
they are not performed with the utmost care.
Before loading, therefore, send away the unauthor-
ized personnel; clear and limit the transfer area and
check the integrity and the suitability of the means
of transport. Besides, check the correct position-
ing of the ramps (external width mm 800x850)
You must make sure that this area is clear and that
there is a sufficient “escape area”, that is a free and
safe area where it is possible to move quickly in case
the load falls.
Before loading, make sure that the body of the means
of transport is large enough to transport the machine
WARNING
The area where you intend to load the machine shall
be a firm level surface to avoid load shift, if any.
- The means of transport shall have the engine shut
off, the gear and the parking brake on.
- The loading and the unloading shall be always
performed with an empty machine (with no load).
- Load the machine by walking at a low travel speed
(1
st
speed and reverse), by being careful to correctly
enter the ramps and to walk on the ramps safely.
Once the machine is loaded onto the means of
transport, make sure it is well locked in its posi-
tion.
Tighten securely the machine onto the platform with
ropes or well-tightened chains to prevent it from
moving,
After transporting it and before untying the machine,
check that the shape and the position of the machine
are not a hazard.
Then remove all ropes and chains and unload it with
the same means and procedures used for loading.
SECTION 4
Use
4.1 BEFORE USING IT
WARNING
Before setting the machine at work, the operator
shall read and understand all parts of this manual
(as well as the engine manual) and in particular
what is written in “Section” (Safety)
Moreover, before starting the machine, check that
the machine is in good working conditions and that
all parts subject to wear are fully efficient.
4.2 STARTING
Before operating the machine and starting to work,
always check that:
- the engine oil is at level (make reference to the en-
gine instructions manual)
- the engine air filter is clean
- the tank has enough fuel.
As for the fuel type, make reference to the engine in-
structions manual by checking the identification data
reported on the engine identification plate.
Содержание F 400
