Firegear KALEA BAY Скачать руководство пользователя

Страница: 16 / 44

Kalea Bay LED Outdoor Fireplace

REV. B Page 16

This fireplace is equipped with LED lighting.

Preparation for the LED lighting a must be planned

before the fireplace finish materials are installed

. After

the fireplace is set in its final location the LED lighting will

need to be installed and tested before finishing materials

are applied. You will need to provide the following:

(1) 120VAC GFCI outlet double gang junction box with a

weatherproof cover. Provides power to LED lights and gas

valve system. Follow local electrical codes for installation.

A RGB control box (with 10’ of wire) is provided with the

fireplace. It must be installed within the framing parameters

of the wire length.

Note:

Additional extension wires are

available in the Accessory section of this manual.

Step 1:

Install the GFCI outlet double gang junction box

with a weatherproof cover on the opposite side of the inlet

gas supply.

Note

: This is not a requirement; however, with the gang

box on the opposite side of inlet will create more room for

LED installation. Fig. 15 shows GFCI gang box installed.

Step 2:

Find mounting location for the GFCI gang box. Fig.

14 shows flat area underneath burner pan. Mount box

underneath the burner pan, below the square (cutout) hole

area. Fig. 15 shows the GFCI outlet double gang junction

box with a weatherproof cover mounted underneath the

fireplace.

Burner Pan

Support leg under fireplace

tto

t fi

GFCI Outlet installed in a double

outlet NEMA 3R enclosure

(Bring electrical up

from underneath

the fireplace)

Fig. 14

GFCI box location under fireplace

GFCI Outlet installed in a double

outlet NEMA 3R enclosure

Fig. 15

Show GFCI box mounted in fireplace

LED LIGHTING INSTALLATION

Fig. 13

Electrical placement.

36” Model = 13”

48“ Model = 18”

60“ Model = 24”

72” Model = 30”

5”

11½”

TYP

Electrical Area (GFCI)

The electric junction box (GFCI) with a weatherproof cover must be installed in

the shaded area shown below. Ensure the j-box is close to the floor area where

the fireplace is sitting and not touching the burnerpan.

Содержание KALEA BAY













































Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды

Firegear KALEA BAY, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды