Firegear KALEA BAY Скачать руководство пользователя

Страница: 27 / 44

Kalea Bay LED Outdoor Fireplace

REV. B Page 27

FINAL PREPARATION

CAUTION:

THIS IS TEMPERED GLASS. DO NOT CHIP

GLASS. CHIPPED TEMPERED GLASS CAN BREAK

WITHOUT WARNING.

Fig. 39

Installing glass panels.

Fig. 38

Glass clips location.

GLASS WINDSHIELD

Glass Holders

INSTALLING REMAINING GLASS CLIPS

Step 26:

Install the remaining (2) glass clips in front of the

LED clips as described on page 17 in steps 3 and 4, Fig.

18.

GLASS PANEL/WINDSHIELD INSTALLATION

Step 27:

• Carefully unpack the glass panels.

• Using gloves carefully lift one glass panel, into the

fireplace opening, over top of the glass clips, and slide

it down into the metal retainer clip, supporting the glass

at the top and bottom as you handle it. See Fig. 39

• As the glass enters the clip the bottom edge of the

glass will rest in place on the bottom of the clip.

• Install the second glass pane in the same manner as

described in Fig. 39.

• Both glass panels should be level when installed.

• Center glass between clips after installation.

Step 1

Step 2

Front of Fireplace

LED

HOT GLASS

WILL

CAUSE BURNS

DO NOT TOUCH

GLASS UNTIL COOLED

NEVER

ALLOW CHILDREN

TO TOUCH GLASS

A barrier designed to reduce the risk of burns

from the hot viewing glass is provided with this

appliance and shall be installed for the

protection of children and other at-risk

individuals.

DANGER

“WARNING: Both glass panels must be installed when

the fireplace is in operation”

Note

: All four (4) glass

panels must be installed on see through fireplaces.

Содержание KALEA BAY













































Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды

Firegear KALEA BAY, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды