Firegear KALEA BAY Скачать руководство пользователя

Страница: 32 / 44

Kalea Bay LED Outdoor Fireplace

REV. B Page 32

Model

Main Burner

Orifice

Low Rate Set

Screw

OFP-36LECO-LPK

OAS-LPR52

ECO-LSS-52

OFP-48LECO-LPK

OAS-LPR48

ECO-LSS-46

OFP-60LECO-LPK

OAS-LPR44

ECO-LSS-42

OFP-72LECO-LPK

OAS-LPR42

ECO-LSS-35

This kit will properly convert the outdoor fireplace to LP gas. Kit contents are: (1) OAS-LP# (Brass orifice) and

(1) ECO-LSS# (Brass low rate set screw), (1) LP Conversion label (placed next to blank space on rating label,

(1) Installation instruction

Fig. 1.

Contents of kit

Step 1

: Turn OFF the gas supply to the outdoor

fireplace and disconnect any electrical power.

Step 2

: Remove the burner pan from the fireplace to

enable conversion access. See installation manual if

necessary.

Step 3

. Disconnect the flex line at the main burner

orifice. Then remove the orifice and flared fitting from the

orifice. Re-tape the flared fitting with the new OAS-LP

orifice per Table 1. Ensure to use gas rated Teflon tape

around the threads or pipe compound. Check for leaks

after conversion is complete.

Fig. 2

Changing main burner orifice

Step 4:

Locate the gas regulator the opposite side of the

valve box. Using a regular size flat bladed screwdriver

remove the aluminum cap and washer from the regulator.

See Fig. 2.

Table 1

Reference information

Fig. 4

Regulator stem shown in NG setting

NOTE:

The plastic stem has a marking on it with an arrow.

Look carefully on the stem, it may be difficult to read.

The gas type is determined with the arrow pointing at the

aluminum cap as seen in Figs. 4 and 5.

Step 5:

On the underneath side of the aluminum cap is a

plastic stem. Using a 6mm wrench remove the stem,

unscrew the stem (counter-clockwise), turn it over and

install the opposite end back into the cap. See Fig. 4.

Fig. 3

Regulator

cap location

NATURAL GAS TO LP GAS CONVERSION

Main Burner Orifice

(OAS-LP#)

Low Rate Set

Screw

(ECO-LSS-#)

Label

This fireplace was

converted to LP gas by

__________________

Date: ______________

Содержание KALEA BAY













































Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды

Firegear KALEA BAY, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды