Firegear KALEA BAY Скачать руководство пользователя

Страница: 10 / 44

Kalea Bay LED Outdoor Fireplace

REV. B Page 10

SINGLE-SIDED FIREPLACE

DIMENSIONS, FRAMING

AND CLEARANCES SECTION

PART NUMBER

DESCRIPTION

QTY.

77146

LED parts box (includes all parts in box)

77102

12VDC adapter for LED light operation

01-487

01-487 connector valve ½”

77151

Ignition screen

77150

Pilot hood

VENT-6X12SS

6x12 vent kit (includes 2- stainless vents;

12- washers, 12- nuts; 12- screws)

77110

LED 24” harness at appliance

77161

ECO OFP 10-foot module harness

77111

LED 10-foot controller harness

AF-4000ADP24-80V5

7.5VDC adapter for gas valve system

77117

RGB control box assembly

(36”) 73232 (48”) 74232

(60”) 75232 (72”) 76232

Windshield parts box

(36”) 73222 (48”) 74222

(60”) 75222 (72”) 76222

LED tray assembly - right

(36”) 73131 (48”) 74131

(60”) 75131 (72”) 76131

Hood (see page 26)

(36”) KB-36-73120

(48”) KB-48-74120

(60”) KB-60-75120

(72”) KB-72-76120

Windshield (see part # for specific sizes)

77145A

Windshield Fastener Bag (includes 1- Left

LED glass clip (77157) 1- Right LED glass

clip (77156) 1- Left Std. glass clip (77155)

1- Right Std. glass clip (77154) &

7- hood screws (77129)

It is important to understand that when installing this outdoor appliance the

installation must follow ANSI standards as described below.

AN OUTDOOR SPACE IS DEFINED AS FOLLOWS PER ANSI Z21.97

Outdoor spaces - An appliance is considered to be outdoors if installed with shelter no more inclusive

than:

• a) With walls on all sides, but with no over-head cover;

• b) Within a partial enclosure which includes an overhead cover and no more than two side walls.

These side walls may be parallel, as in a breezeway, or at right angles to each other; or

• c) Within a partial enclosure which includes an overhead cover and three sidewalls, as long as

30% or more of the horizontal periphery of the enclosure is permanently open.

This fireplace comes with two boxe

prepackaged inside and outside the fireplace. Do

not discard any boxes unless noted to do so. Read the list below for the contents.

Содержание KALEA BAY













































Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды

Firegear KALEA BAY, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды