Firegear KALEA BAY Скачать руководство пользователя

Страница: 17 / 44

Kalea Bay LED Outdoor Fireplace

REV. B Page 17

Step 3:

Locate the wire grommets inside the firebox. See

Fig. 16. Directly above them will be a series of metal

bridges to install the glass panel clips. Remove the glass

panel clips from the glass panel packaging.

CAUTION:

The metal clips may have sharp edges, handle with care.

Peel the plastic coating from each glass panel clip

before installing.

There will be (4) glass clips. The two

longest clips are use for the LED tray assembly and the

shorter glass clips will installed in front of the LED clips.

The LED clips (two longest clips) are installed first, closest

to the burner tray.

Note:

There are two right side and two

left side clips supplied.

Install the LED glass clips by sliding them down through

the metal bridges as shown in Fig. 17. Install (1) clip on the

left and (1) clip on the right side of the inner fireplace side

panel.

Note:

If you are preparing a see-through fireplace

you will install a total of (8) glass clips, two for each open

side. The additional clips are supplied with the see-through

conversion kit.

Fig. 17

Shows both glass clips being installed on

right side of fireplace

Wire Grommets

Metal Bridges

Fig. 16

Locating wire grommets

Step 4

: After each

LED glass clip is installed, use a flat

blade screw and carefully bend the bottom tab out and

upward to lock it into position. Use a fingertip or pliers to

press the tab flat against the metal bridge. See Fig. 18.

Fig. 18

Installing windshield clips

LED LIGHTING INSTALLATION

Step 1

Step 2

ft F

lip

Left

Back

Gla

ss C

lip

LED

Bend Lower Tabs Upward

to Lock Clip into Position

Locked

Tab

Loose

Tab

Right Side Panel

Содержание KALEA BAY













































Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды

Firegear KALEA BAY, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KALEA BAY

Отзывы:

Похожие инструкции для KALEA BAY

Бренды по названию

Популярные бренды