Festo MSE6-C2M Скачать руководство пользователя страница 62

Страница: 62 / 104

Festo — MSE6-C2M — 2022-08b

Commissioning

Fig. 26: DIL switches on bus node CPX-M-FB44

DIL switch 1: operating mode

DIL switch 2: diagnostic mode

Memory card

1. Switch off the power supply.
2. Unscrew the retaining screws of the cover.
3. Remove the cover

2 DIL switches are visible.

4. Use DIL switch 1 to set the operating mode.
5. Set the diagnostic mode with DIL switch 2.
6. Fit the cover.
7. Tighten the retaining screws of the cover. Tightening torque: 0.4 Nm ± 10 %.

Setting operating mode, DIL switch 1

All switch elements of the DIL switch 1 must be in the OFF position.

DIL switch 1

Setting operating mode

DIL 1.1: OFF
DIL 1.2: OFF
(factory setting)

Remote I/O operating mode
All functions of the energy efficiency module are controlled directly
by the controller or by a higher-level PLC.

DIL 1.1: ON
DIL 1.2: OFF

Not supported by the energy efficiency module.
DIL switch elements 1.1 and 1.2 must be in the OFF position.

DIL 1.1: OFF
DIL 1.2: ON

DIL 1.1: ON
DIL 1.2: ON

Tab. 44: Setting the operating mode with DIL switch 1

Содержание MSE6-C2M








































































































Результаты поиска

Содержание MSE6-C2M

Отзывы:

Похожие инструкции для MSE6-C2M

Бренды по названию

Популярные бренды

Festo MSE6-C2M, Руководство по эксплуатации

Результаты поиска

Содержание MSE6-C2M

Отзывы:

Похожие инструкции для MSE6-C2M

Бренды по названию

Популярные бренды