Festo MSE6-C2M Скачать руководство пользователя страница 55

Страница: 55 / 104

Festo — MSE6-C2M — 2022-08b

Commissioning

DIL switch 1.1

Setting operating mode

DIL 1.1: ON

Not supported.

The 1.1 DIL switch element must be in the OFF position.

Tab. 35: Setting the operating mode with DIL switch 1.1

DIL switch 1.2

Setting the protocol

DIL 1.2: OFF
Factory setting

‘EtherNet/IP’ protocol.

The energy efficiency module uses the ‘EtherNet/IP’ protocol.

DIL 1.2: ON

Protocol ‘Modbus TCP’
The energy efficiency module uses the ‘Modbus TCP’ protocol.

Tab. 36: Setting the protocol with DIL switch 1.2

Setting diagnostic mode, DIL switch 2

DIL switch 2

Setting diagnostic mode

DIL 2.1: OFF
DIL 2.2: OFF
Factory setting

‘I/O diagnostics interface’ and status bits are switched off, + 0 byte
I/0 byte O.

DIL 2.1: OFF
DIL 2.2: ON

The status bits are on, + 1 byte I/0 byte O

DIL 2.1: ON
DIL 2.2: OFF

The ‘I/O diagnostics interface’ is switched on, + 2 bytes I/2 byte
O

DIL 2.1: ON
DIL 2.2: ON

Reserved for future extensions.

1) The status bits occupy 1 byte address space, 8 I bits
2) The I/O diagnostics interface occupies 4 bytes address space, 16 I and 16 O bits

Tab. 37: Setting diagnostic mode using DIL switch 2

Set IP addressing, DIL switch 3

DIL switches 3.1 … 3.8 are used to set the type of addressing or the IP address of the energy efficiency
module.

Содержание MSE6-C2M








































































































Результаты поиска

Содержание MSE6-C2M

Отзывы:

Похожие инструкции для MSE6-C2M

Бренды по названию

Популярные бренды

Festo MSE6-C2M, Руководство по эксплуатации

Результаты поиска

Содержание MSE6-C2M

Отзывы:

Похожие инструкции для MSE6-C2M

Бренды по названию

Популярные бренды