Festo MSE6-C2M Скачать руководство пользователя страница 61

Страница: 61 / 104

Festo — MSE6-C2M — 2022-08b

Commissioning

Connection TP1, TP2

Pin

Signal

Explanation

TD+

Transmit Data, TD+

RD+

Receive Data, RD +

TD–

Transmitted data –

RD–

Received data –

Housing

Shield/FE Shield/functional earth

Tab. 42: Pin allocation of network interface TP1 and TP2, PROFINET

Network connections on the bus node CPX(-M)-FB44
The bus node has 2 RJ45 push-pull sockets for connection to the network, AIDA-compliant

RJ45 bushing

Pin

Signal

Explanation

TD+

Transmit Data, TD+

TD-

Transmitted data –

RD+

Receive Data, RD +

n.c.

Not connected

n.c.

Not connected

RD-

Received data –

n.c.

Not connected

n.c.

Not connected

Housing

Shield/FE Shield/functional earth

Tab. 43: Pin allocation of the network interfaces RJ45, PROFINET

Connecting the energy efficiency module to the network
1. Connect the bus node to the network with the NECU-MS-D12G4-C2-ET or FBS-RJ45-PP-GS con-

nector.

2. Seal the unused connections with cover caps or blanking plugs to achieve the specified degree of

protection.

8.5.4

Setting DIL switches

You can set the following parameters with the DIL switches:

–

The operating mode. The energy efficiency module only supports the Remote I/O operating mode in
conjunction with the bus node CPX(-M)-FB44.

–

The diagnostics mode.

Содержание MSE6-C2M








































































































Результаты поиска

Содержание MSE6-C2M

Отзывы:

Похожие инструкции для MSE6-C2M

Бренды по названию

Популярные бренды

Festo MSE6-C2M, Руководство по эксплуатации

Результаты поиска

Содержание MSE6-C2M

Отзывы:

Похожие инструкции для MSE6-C2M

Бренды по названию

Популярные бренды