REV. 07/2019
ELECTRICAL SYSTEM
8
151
Error Message
Possible cause
Fault elimination
Error
Error text
228
POSITION ERROR
This alarm occurs for an error in
the redundant test of the feedback
sensors.
Check the potentiometer
connected to CNB#6 is right
working. If toggle switches
are connected to CNA#2
and CNA#3, verify they
are right working and the
setting AUX FUNCTION
11 is correct. Verify also
the sensor bearing in the
motor (encoder) has not a
slip (the sensor bearing has
two rings: one is connected
to the rotor shaft; the other
is connected to the motor
frame. Check these two
rings are strictly connected
to their structure without
slip.
238
EPS NOT ALIGNED
This is a real alarm that cut off
the traction. It occurs at the initial
alignment if the straight-ahead
condition is not matched within
6sec. Throughout this 6 secs delay,
the steer is not activated yet, the
safety relays are open and the
traction is stopped.
——
239
WAITING FOR TRAC
At key-on the eps-ac0 needs an
assent from the traction controller
to close the safety contacts and to
turn onto operational mode.
Until this assent is not relieved, this
warning occurs. The steer is not
activated yet and the safety relays
remain open when this warning is
present.
——
241
ENCODER ERROR
I t o c c u r s w h e n E N C O D E R
CONTROL is set ON and the real
frequency does not pursuit the
commanded frequency
This condition is several
times due to either, a
mismatching between the
Encoder resolution used
in the SW and the real
encoder resolution, or a
wrong connection between
the two encoder channels.
In this latest case exchange
in between the two encoder
channels.
Содержание LIST JX0
