REV. 07/2019
ELECTRICAL SYSTEM
8
142
Error Message
Possible cause
Fault elimination
Error
Error text
208
EEPROM KO
the connection of the EEPROM
is not ok
This type of fault is related to
internal components. Replace
the logic board.
209
PARAM RESTORE
The controller has restored the
default settings. If a CLEAR
EEPROM has been made
before the last key re-cycle,
this warning informs you that
EEPROM was correctly cleared.
"1- A travel demand or a pump
request does cancel the alarm.
2- If the alarm appears at
key-on without any CLEAR
EEPROM performed,
replace the controller."
210
WRONG RAM MEM.
The algorithm implemented to
check the main RAM registers
finds wrong contents: the
register is “dirty”. This alarm
inhibits the machine operations.
"Try to switch the key off
and then on again, if the
alarm is still present replace
the logic board."
211
STALL ROTOR
The traction rotor is stuck or the
encoder signal is not correctly
received by the controller
"1- Check the encoder
condition.
2- Check the wiring.
3- Through the TESTER
function, check if the sign of
FREQUENCY and
ENCODER are the same and
if they are different from zero
during a
traction request.
4- If the problem is not solved,
replace the logic board."
213
POSITIVE LC OPEN
The positive voltage of LC is
different from expected.
"1- Verify LC coil is properly
connected.
2- Verify CONF. POSITIVE LC
parameter is set in accordance
with the actual coil positive
supply (see paragraph 8.2.5).
Software, depending on the
parameter value, makes a
proper diagnosis; a mismatch
between the hardware and the
parameter configuration could
generate a false fault.
3- In case no failures/problems
have been found, the problem
is in the controller, which has
to be replaced."
Содержание LIST JX0
