REV. 07/2019
ELECTRICAL SYSTEM
8
109
8.6 Tilt Switch
(
Optional)
This forklift is equipped with a level sensor,
namely, tilt switch. When the tilt angle exceeds
4.5 degrees, the cabin will be lifted, and the tilt
buzzer will emit continuous alarm. The lifting
operations can only be carried out on a level
ground.
8.6.1 Removal and Installation
-
-
-
-
-
-
-
Press the lift button (2, Figure50107) and low
control button (3, Figure50107) to lift mast to
proper height;
Engage the emergency stop switch and turn
off key switch;
Remove the cover(see section 4.3);
Disconnect the connector of tilt switch(1);
Unscrew the four bolts(2), remove level
sensor plate with tilt switch, unscrew the four
bolts(3), remove tilt switch;
Disconnect the connector of tilt buzzer(5);
Unscrew the three bolts(6), remove tilt
buzzer.
Removal
Tilt switch is mounted on the chassis bottom
plate underneath the rear cover. (See Section
3.1.11)
Installation
-
Install according to the reverse order of rem-
oval.
8.6.2 Faults and Causes
1
Fault
Under lifting state, travel on the
ramp greater than 4.5 degrees, no
alarm sound is heard
Cause
a. Tilt switch failure;
b. Tilt buzzer failure;
c. Control circuit not conducted.
Checking
-
Check if the tilt buzzer, tilt switch and its
wiring harness are in good condition, and if
the connectors are connected securely.
8.6.3 Checking and Testing
-
-
-
-
Check if the tilt switch and tilt buzzer circuit is
conducted;
Energize the tilt buzzer with a voltage of 24V;
If the buzzer does not sound, replace the
buzzer;
If the buzzer sounds, replace the tilt switch.
Testing
8.6.4 Control Circuit Troubleshooting
Tilt Switch Control Circuit
(Figure 50523)
Check if the circuit is broken by using a multi-
meter:
-
-
Set the multimeter to ON-OFF;
Check if #3/#18/#79/#33 circuit (circuit betw-
een tilt switch and controller) is conducted.
Содержание LIST JX0
