EDM Solution 862 Скачать руководство пользователя страница 8

Страница: 8 / 262

Arming The System In STAY Mode 1 _____________________________________________________________ 54

Entry Guard Timer For STAY Mode ____________________________________________________________ 54

Forced Arming _____________________________________________________________________________ 55

Disarming The System From STAY Mode 1 ________________________________________________________ 56

Arming The System In STAY Mode 2 _____________________________________________________________ 57

Entry Guard Timer For STAY Mode ____________________________________________________________ 57

Forced Arming _____________________________________________________________________________ 57

Disarming The System From STAY Mode 2 ________________________________________________________ 58

Codepad Duress Alarm_________________________________________________________________________ 59

Codepad Panic Alarm __________________________________________________________________________ 59

Codepad Fire Alarm ___________________________________________________________________________ 59

Codepad Medical Alarm________________________________________________________________________ 59

Isolating Zones ________________________________________________________________________ 60

Standard Isolating ___________________________________________________________________________ 61

Code To Isolate_____________________________________________________________________________ 62

Fault Analysis Mode____________________________________________________________________ 63

Fault Descriptions _____________________________________________________________________________ 64

Low Battery _______________________________________________________________________________ 64

Date and Time______________________________________________________________________________ 64

Sensor Watch ______________________________________________________________________________ 64

Horn Speaker Monitor _______________________________________________________________________ 64

Telephone Line Fault ________________________________________________________________________ 64

Fault ___________________________________________________________________________________ 64

Fuse Fail __________________________________________________________________________________ 65

Communication Failure ______________________________________________________________________ 65

AC Mains Failure ___________________________________________________________________________ 66

Remote Radio Transmitter Operations ________________________________________________ 67

Remote Radio Transmitter Operations ____________________________________________________ 68

Indications Upon Remote Radio Transmitter Operations _______________________________________________ 68

Remote Radio User Code Priority Levels___________________________________________________________ 68

Changing Or Deleting Remote Radio User Codes ____________________________________________________ 69

2 Channel Radio Remote Hand Held Transmitter Operations ___________________________________________ 71

Arming In AWAY Mode _____________________________________________________________________ 71

Disarming From AWAY Mode ________________________________________________________________ 71

Arming In STAY Mode 1 _____________________________________________________________________ 71

Disarming From STAY Mode 1 ________________________________________________________________ 71

Panic Alarm _______________________________________________________________________________ 71

4 Channel Radio Remote Hand Held Transmitter Operations ___________________________________________ 72

Arming In AWAY Mode _____________________________________________________________________ 72

Disarming From AWAY Mode ________________________________________________________________ 72

Arming In STAY Mode 1 _____________________________________________________________________ 72

Disarming From STAY Mode 1 ________________________________________________________________ 72

Panic Alarm _______________________________________________________________________________ 72

Turning Output 1 ON ________________________________________________________________________ 73

Turning Output 1 OFF _______________________________________________________________________ 73

Turning Output 2 ON ________________________________________________________________________ 73

Turning Output 2 OFF _______________________________________________________________________ 73

System Functions _________________________________________________________________ 75

System Functions ______________________________________________________________________

Installer Code Functions ________________________________________________________________________ 76

Reserved __________________________________________________________________________________ 76

Set The Number Of Days Until The First Test Report _______________________________________________ 77

Changing Domestic Phone Numbers ____________________________________________________________ 78

Change Telco Arm/Disarm Sequence____________________________________________________________

Setting STAY Mode 2 Zones __________________________________________________________________ 85

Satellite Siren Service Mode___________________________________________________________________ 86

Turning Telephone Monitor Mode On/Off________________________________________________________ 87

Walk Test Mode ____________________________________________________________________________ 87

Event Memory Recall Mode___________________________________________________________________ 88

Reserved __________________________________________________________________________________ 88

Содержание Solution 862







































































































































































































































































Результаты поиска

Содержание Solution 862

Отзывы:

Бренды по названию

Популярные бренды

EDM Solution 862, Руководство по установке

Результаты поиска

Содержание Solution 862

Отзывы:

Бренды по названию

Популярные бренды