manualshive.com logo in svg

EDM Solution 862, Руководство по установке

Поделиться
Скачать
EDM Solution 862 Скачать руководство пользователя страница 193

 

08

 

Exit Warning Finished

 

This output operates when the exit time has expired when the system has been 
armed in AWAY Mode, STAY Mode 1 or STAY Mode 2.  The output will reset 
when the system has been disarmed.  
 

09

 

Kiss-Off After Exit Time

 

This output will operate after the first successful transmission to the base station 
receiver when exit time has expired.  The output will reset when the system has been 
disarmed. 
 

0

 

Entry Warning

 

This output will operate when either Entry Timer 1, Entry Timer 2 or Entry Guard 
Timer For STAY Mode are operating.  The output will reset when the entry time 
expires.  
 

0

  

Entry W Day Alarm Resetting 

This output combines both Entry Warning and Day Alarm Resetting so that either of 
these two events will activate the output.   
 
If the output has been triggered by either Entry Timer 1, Entry Timer 2, or Entry 
Guard Timer For STAY Mode, the output will reset once the entry timer has expired 
or the system has been disarmed.  
 
If a zone programmed for day alarm has triggered during the disarmed state, the 
output will reset when the zone has resealed.  

 alarm may be turned on and off 

by holding down the 

4

 button.  Refer to Day Alarm Zones on page 156 for 

programming zones to operate for day alarm. 
 

0

 

Exit W Entry W Day Alarm Resetting 

This output combines exit warning, entry warning and day alarm so that any of these 
three events will activate the output. 
 
This output will activate once the system has been armed in AWAY Mode, STAY 
Mode 1 or STAY Mode 2 irrespective of any zones being sealed or unsealed until 
exit time expires. 
 
The next time the output will activate will be during entry time and will reset once 
entry time has expired or the system has been disarmed.   his output will also 
operate when the Entry Guard Timer For STAY Mode is timing. 
 
If a zone programmed for day alarm has triggered during the disarmed state, the 
output will reset when the zone has resealed.  

 alarm may be turned on and off 

by holding down the 

4

 button.  Refer to Day Alarm Zones on page 156 for 

programming zones to operate for day alarm. 
 

0

 

Day Alarm Resetting

 

This output will operate when a zone programmed for day alarm has been triggered.  
The output will reset when the day alarm zone has resealed. Day alarm may be 

turned on and off by holding down the 

4

 button.  Refer to Day Alarm Zones on 

page 156 for programming zones to operate for day alarm. 
 

0

 

Day Alarm Latching 

This output will operate when a zone programmed for day alarm has been triggered.  

The output will reset when the 

 button has been pressed.   ay alarm may be 

turned on and off by holding down the 

4

 button.  Refer to Day Alarm Zones on 

page 156 for programming zones to operate for day alarm. 

Programmable Outputs 

193 

 

Electronics Design and Manufacturing Pty Limited 

ISSUE130 

Day

T

Day

D

Содержание Solution 862







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды