manualshive.com logo in svg

EDM Solution 862, Руководство по установке

Поделиться
Скачать
EDM Solution 862 Скачать руководство пользователя страница 153

User Codes 

153 

User Code Priority 

There are ten different priority levels that can be allocated to the user code.  Each priority level 
allows or restricts the functions that different user code holders may perform. 

Priority Level 

Description 

0 

Arm/Disarm 

1 

Arm Only 

2 

Arm/ Open/Close Report 

3 

Arm Only + Close Report 

4 

Arm/ Code To Isolate 

6 

Arm/ Code To I Open/Close Report 

8 

Arm/ Master Code Functions 

10 

Arm/ Master Code Fun Open/Close Report 

12 

Arm/ Master Code Fun Code To Isolate 

14 

Arm/ Master Code Fun Code To I Open/Close 
Report 

Meaning 

Description 

Arm/Disarm 

If the user code has this option included in the priority level, the user 
can arm and disarm the system.  A closing report will only occur after 
a previous code that has the ability to send an opening report has 
disarmed the system. 

Arm Only 

If the user code has this option included in the priority level, the user 
can only arm the system and cannot disarm the system. A closing 
report will only occur after a previous code that has the ability to send 
an opening report has disarmed the system. 

Open/Close Reports 

If the user code has this option included in the priority level, the user 
will always send open and close reports back to the monitoring station 
upon disarming and arming the system. This option requires 
Open/Close reports in “LOCATION 333 - 334” on page 179 to be 
enabled for it to be effective. 

Code To Isolate 

If any user code has this option included in the priority level, the 
method of standard isolating is disabled from the system and only 
user codes with code to isolate selected can isolate zones prior to 
arming the system using the method of code to isolate.  Refer to 
Isolating Zones on page 60 for more information. 

Master Code Functions 

If any user code has this option included in the priority level, the user 
has access to all Master Code Functions. 

Table 68: User Code Priority Levels 

Once user code priority levels 4, 6, 12 or 14 have been programmed to any of the 
available 8 user codes, the method of standard isolating will no longer operate.  Only
those user codes with the priority level of 4, 6, 12 or 14 will be able to isolate zones using
the method code to isolate. 

Electronics Design and Manufacturing Pty Limited 

ISSUE130 

Содержание Solution 862







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды