manualshive.com logo in svg

EDM Solution 862, Руководство по установке

Поделиться
Скачать
EDM Solution 862 Скачать руководство пользователя страница 45

Codepad Indicators 

45 

STAY Indicator 

The 

STAY

 indicator is used to display that the system is armed in STAY Mode 1 or STAY 

Mode 2.  The 

STAY

 indicator will also flash in unison with the 

AWAY

 indicator when 

Installer’s Programming Mode or Master Code Functions are used. 

Refer to page 54 for the different methods of arming the system in STAY Mode 1.  Refer to 
Zone Options 1 on page 167 for information on setting zones to be automatically isolated  in 
STAY Mode 1.  For the method of arming the system in STAY Mode 2, refer to page 57. 
Refer to Setting STAY Mode 2 Zones on page 85 when using the Installer Code or Setting 
STAY Mode 2 Zones on page 101 when using the Master Code. 

Indicator 

Definition 

On 

System Is Armed In STAY Mode 1 Or STAY Mode 2 

Off 

System Is Not Armed In STAY Mode 

Flashing 

Zone Isolating Mode Or Setting STAY Mode 2 Zones 

Table 10: STAY Indicator 

MAINS Indicator 

The 

MAINS 

indicator is used to display that the systems AC mains supply is normal or has 

failed. 

When programming numbers (i.e. Installer’s Programming Mode or Master Code Functions), 
the 

MAINS

 indicator will illuminate when you program numbers between 10 and 15.  The 

MAINS

 indicator represents digit 10 plus the value of the illuminated zone indicator (e.g.: If 

you program a twelve, the 

MAINS

 indicator and zone 2 will illuminate). 

Indicator 

Definition 

On 

AC Mains Power Normal 

Flashing 

AC Mains Failure 

Table 11: MAINS Indicator 

FAULT Indicator 

The 

FAULT

 indicator is used to display that the system has detected a system fault.  Refer to 

Fault Analysis Mode on page 63 for more information on system faults. 

Every time a new system fault has been detected (e.g.: 

FAULT

 indicator flashing), the codepad 

will begin to beep once every minute. 

Pressing the 

button once will cancel the once a minute beep and acknowledge the fault 

(e.g.: 

FAULT

 indicator on). 

Indicator 

Definition 

On 

There Is A System Fault That Needs To Be Rectified 

Off 

The System Is Normal, There Are No Faults 

Flashing 

There Is A System Fault Waiting To Be Acknowledged 

Table 12: FAULT Indicator 

Electronics Design and Manufacturing Pty Limited 

ISSUE130 

Содержание Solution 862







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды