manualshive.com logo in svg

EDM Solution 862, Руководство по установке

Поделиться
Скачать
EDM Solution 862 Скачать руководство пользователя страница 220

220 

Solution 862

 Installation Manual 

Consumer Options 2 

LOCATION 429 

2 

Option 

Description 

1 

Codepad Display Extinguish After 60 Seconds 

2 

Single Button Arming Allowed (AWAY/STAY Mode 1 & 2) 

4 

Single Button Disarming Allowed (STAY Mode 1 & 2) 

8 

Alarm Memory Reset On Disarm 

1 

2 

4 

8 

Table 130: Consumer Options 2 

Codepad Display Extinguish After 60 Seconds 

If this option has been selected, all indicators on the remote codepad display will extinguish if 
a button is not pressed for 60 seconds.  The indicators will illuminate when there is an alarm 
(except a silent alarm), when a button is pressed on the codepad, when the AC mains fail 
beeps, or if the entry timer has been activated. 

Single Button Arming Allowed (AWAY Mode/STAY Mode 1 & 2) 

If this option has been selected, the hold down functions for arming in AWAY Mode, STAY 
Mode 1 and STAY Mode 2 will be functional.  Refer to Hold Down Functions on page 107 for 
more information. 

Single Button Disarming Allowed (STAY Mode 1 & 2) 

This option will only operate when Option 2 in this location has also been selected.  This 
option will allow hold down functions for disarming from STAY Mode 1 and STAY Mode 2. 
Refer to Hold Down Functions on page 107 for more information. 

Alarm Memory Reset On Disarm 

This option allows the memory of alarm events to be cleared from the remote codepad when 
the system has been disarmed.  If this option has not been selected, the system will need to be 
armed and disarmed again to clear alarm memory from the remote codepad. 

ISSUE130 

Electronics Design and Manufacturing Pty Limited 

Содержание Solution 862







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды