manualshive.com logo in svg

EDM Solution 862, Руководство по установке

Поделиться
Скачать
EDM Solution 862 Скачать руководство пользователя страница 42

42 

Solution 862

 Installation Manual 

Defaulting The Control Panel 

If the 

Solution 862

 control panel does not have "LOCATION 900" programmed as 15, 

follow the procedure outlined below to successfully default the control panel back to the 
factory default settings. 

How To Default The Control Panel Via Installer Code 

1. 

Enter Installer Programming Mode. 

(e.g.. 

1234

followed by the 

#

button).  Two beeps will be heard.  The 

STAY 

and 

AWAY 

indicators will begin to flash to indicate that you have accessed 

programming mode. 

2. 

 

Enter Installer’s Programming Command 

965

followed by the 

#

button. 

Two beeps will be heard after the control panel has successfully been defaulted. 

3. 

 

Enter Installer’s Programming Command 960 followed by the # button. 
Two beeps will be heard.  The 

STAY

 and 

AWAY

 indicators will cease to flash and the 

system will return to the disarmed state. 

The control panel has now been successfully defaulted back to the factory default 
settings. 

How To Default The Control Panel Via Default Button 

1. 

Disconnect the AC mains supply and the backup battery from the control panel. 

2. 

 

Hold down and continue to hold down the DEFAULT button. 
The default button is located at the top of the PCB next to the PROGRAMMING KEY 
connecting socket. 

3. 

Reconnect the AC mains supply to the control panel. 

4. 

 

After reconnecting the AC mains supply, wait for 3-5 seconds before releasing the 
DEFAULT button. 

5. 

Disarm the system using the default Master Code (e.g.. Enter 

2580

followed by 

the 

#

button). 

The control panel has now been successfully defaulted back to the factory default 
settings. 

If you hear the dialler seize relay (RL2) click four times while attempting to default the
control panel, this would indicate that the feature of defaulting the control panel has 
been disabled in “LOCATION 900” on page 41.  The control panel will need to be returned 
to Electronics Design and Manufacturing Pty Limited for exchange where a service fee 
will be charged to unlock the control panel's memory if the Installer Code is not known. 

ISSUE130 

Electronics Design and Manufacturing Pty Limited 

Содержание Solution 862







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды