manualshive.com logo in svg

EDM Solution 862, Руководство по установке

Поделиться
Скачать
EDM Solution 862 Скачать руководство пользователя страница 54

54 

Solution 862

 Installation Manual 

Arming The System In STAY Mode 1 

Arming the system in STAY Mode 1 is only used when the perimeter and unused areas of the 
premises need to be armed to detect any would be intruder from entering the premises, at the 
same time allowing you to move freely within an area which has been automatically isolated. 

Programming zones to be automatically isolated in STAY Mode 1 can only be programmed by 
the installer.  Refer to Zone Options 2 on page 171 for further information on setting zones to 
be automatically isolated in STAY Mode 1. 

There are two methods for arming your system in STAY Mode 1.  Method one is standard and 
will always operate.  Method two is optional and needs Option 2 in "LOCATION 429" to be 
enabled on page 220. 

Entry Guard Timer For STAY Mode 

When arming the system in STAY Mode 1, an optional entry timer called Entry Guard Timer 
For STAY Mode may be used to delay the sirens, strobe and bell outputs if a zone that has not 
been automatically isolated has triggered into alarm condition.  Entry Guard Timer For STAY 
Mode is the delay time used for all zones except 24 hour zones when the system is armed in 
STAY Mode 1 or STAY Mode 2. 

If the Entry Guard Timer For STAY Mode has been programmed and a zone that has not been 
automatically isolated has triggered, the codepad will beep twice a second until the Entry 
Guard Timer For STAY Mode has expired or the system has been disarmed.  If the alarm 
condition has not been reset before Entry Guard Timer For STAY Mode expires, the strobe, 
bell and siren outputs will activate into alarm. 

Single button arming in STAY Mode 1 will report as user code number 16. 

Method One 

How To Arm The System In STAY Mode 1 

1. 

 

Enter your

 followed by the 

button. 

Two beeps will be heard and the 

STAY 

indicator will illuminate.  Exit time will now 

commence. 

Any zones that have been programmed to be automatically isolated in STAY Mode 1 
will begin to flash until exit time expires.  At the end of exit time, the 

ZONE

 indicators 

will extinguish and the codepad will give one short beep. 

+ 

ISSUE130 

Electronics Design and Manufacturing Pty Limited 

Содержание Solution 862







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды