manualshive.com logo in svg

EDM Solution 862, Руководство по установке

Поделиться
Скачать
EDM Solution 862 Скачать руководство пользователя страница 66

66 

Solution 862

 Installation Manual 

AC Mains Failure 

An AC mains supply failure will automatically flash the 

MAINS

 indicator.  If the AC mains 

supply has been disconnected continuously for more than two minutes, the remote codepad 
will beep the codepad buzzer once every minute.  If the control panel has been programmed to 
report an AC mains fail to a base station receiver,”AC Fail" report (Contact ID Event Code 
301) will be transmitted. 

The 

MAINS

 indicator will cease to flash as soon as the AC mains supply has been reconnected. 

When the AC mains supply has been continuously connected for a period of two minutes, the 
codepad will cease the once a minute beep and”AC Fail” restore report will be transmitted to 
the base station receiver. 

If Option 1 – Enable AC Fail In 1 Hour in “LOCATION 426” on page 217 has been enabled, 
the codepad will flash the 

MAINS 

indicator as soon as the AC mains supply has been 

disconnected and will not activate the dialler or the codepad buzzer unless the AC mains 
supply has been disconnected continuously for a period of 1 hour. 

If Option 2 – Ignore AC Mains Fail in “LOCATION 426” on page 217 has been enabled, the 
codepad will not indicate when the AC mains supply has failed, but the control panel will still 
report if enabled an "AC Fail" report. 

ISSUE130 

Electronics Design and Manufacturing Pty Limited 

Содержание Solution 862







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды