Edelbrock Pro-Tuner Скачать руководство пользователя страница 177

Страница: 177 / 235

Advanced Tuning with the Pro Tuner System

177

5.3

Toggle Closed Loop

Visit us at: http://www.edelbrock.com

Toggle Closed Loop

This This feature toggles on/off the

Closed Loop Correction

(CLC) feature.

The driver's side sensor is always the

primary

sensor.

Always plug into the driver side only

when using a single sensor. If using dual sensors, the system will perform the closed loop
correction based upon the leanest bank's feedback.

The

Closed Loop

feature uses the O2 sensor to make fueling corrections as part of the

Learning/Adaptation feature. There may be situations where you wish to DISABLE this
feature so that you can make adjustments to the VE map or Air Fuel Target map without
the system adapting the CLC map.

In that case, you would toggle the Closed Loop Feature to

DISABLED

(Green LED will be

dark) and then make your changes. This will disable the Closed Loop control until you
toggle the button back on.

Содержание Pro-Tuner












































































































































































































































Результаты поиска

Содержание Pro-Tuner

Отзывы:

Похожие инструкции для Pro-Tuner

Бренды по названию

Популярные бренды

Edelbrock Pro-Tuner, Руководство пользователя

Результаты поиска

Содержание Pro-Tuner

Отзывы:

Похожие инструкции для Pro-Tuner

Бренды по названию

Популярные бренды