Eaton Power Xpert Plus 1, Инструкция по установке и эксплуатации, Страница: 31 / 194

UPS INSTALLATION PLAN AND UNPACKING
Power Xpert 9395 UPS (450–550 kVA) Installation and Operation Manual 164201701 Rev 3
www.eaton.com/powerquality
3-9
For external wiring requirements, including the minimum AWG size of external wiring,
see Table 3‐4 for common battery system installations, Table 3‐5 for separate battery
system installations, or Table 3‐6 for separate rectifier feed installations. Wire sizes
listed are for copper wiring only.
Table 3‐4. Input/Output Ratings and External Wiring Requirements for the 9395-550/450, 9395-550/500, and 9395-550/550 – Common Battery
Basic Unit Rating
Units Rating 50/60 Hz
kVA
kW
450
409 450
409 500
455 500
455 550
500 550
500
Input and Output Voltage Volts 400/400 480/480 400/400 480/480 400/400 480/480
AC Input to UPS Rectifier (0.98 Minimum pF)
Full load current plus battery recharge current
(3) Phases, (1) Ground
A
Amps 741 617 823 686 905 754
Minimum Conductor Size
Number per Phase AWG or kcmil
(each)
300
(4)
4/0
(3)
300
(4)
350
(3)
300
(4)
350
(3)
AC Input to UPS Bypass (Four Wire)
Full Load Current
(3) Phases, (1) Ground
B
Amps 650 541 722 601 794 662
Minimum Conductor Size
Number per Phase AWG or kcmil
(each)
350
(3)
4/0
(3)
350
(3)
4/0
(3)
350
(3)
350
(3)
AC Input to UPS Bypass (Five Wire)
Full Load Current
(3) Phases, (1) Neutral, (1) Ground
B
Amps 650 541 722 601 794 662
Minimum Conductor Size
Number per Phase AWG or kcmil
(each)
500
(3)
250
(3)
500
(3)
300
(3)
500
(3)
300
(4)
DC Input from Each Battery Cabinet to UPS or Battery
Disconnect
(1) Positive, (1) Negative
C
Total Amps 902 902 1002 1002 1103 1103
Minimum Conductor Size
Number per Pole AWG or kcmil
(each)
500
(1)
500
(1)
500
(1)
500
(1)
500
(1)
500
(1)
DC Input from Battery Disconnect to UPS
(1) Positive, (1) Negative
C
Total Amps 902 901 1002 1001 1103 1101
Minimum Conductor Size
Number per Pole AWG or kcmil
(each)
350
(6)
400
(4)
350
(6)
350
(6)
350
(6)
350
(6)
AC Output to Critical Load (Four Wire)
Full Load Current
(3) Phases, (1) Ground
D
Amps 650 541 722 601 794 662
Minimum Conductor Size
Number per Phase AWG or kcmil
(each)
350
(3)
4/0
(3)
350
(3)
4/0
(3)
350
(3)
350
(3)
AC Output to Critical Load (Five Wire)
Full Load Current
(3) Phases, (1) Neutral, (1) Ground
D
Amps 650 541 722 601 794 662
Minimum Conductor Size
Number per Phase AWG or kcmil
(each)
500
(3)
250
(3)
500
(3)
300
(3)
500
(3)
300
(4)
NOTE Callout letters
A
,
B
,
C
, and
D
map to Figure 6‐6 or Figure 6‐8 starting on page 6-9. Callout letters
A
,
C
, and
D
map to Figure 6‐10 or Figure 6‐12
starting on page 6-13.
NOTE Bypass wiring data is not applicable to IOM configurations.