Eaton Power Xpert Plus 1 Скачать руководство пользователя страница 185

Страница: 185 / 194

UPS MAINTENANCE

Power Xpert

9395 UPS (450–550 kVA) Installation and Operation Manual

164201701 Rev 3

www.eaton.com/powerquality

9-3

ISBM Air Filter Locations

UPM Air Filter Locations

ÄÄÄÄÄÄÄ

ÄÄÄÄÄ

ÄÄÄÄ

Figure 9‐1. UPS Filter Locations

Verify washed filters are thoroughly dry before reinstalling.

Push the washed or new foam filters over the screw heads on the cabinet
mounted studs until seated against the cabinet.

Reinstall the UPM front panel removed in Step a and secure with the
retained hardware.

Close the front door and secure the latch.

If the UPS is a Plus 1 model, check the Field Installed UPM (FI-UPM) air filter
(located behind the front panel) and wash or replace as necessary. See Figure 9‐2
for the filter location. The FI-UPM filter size is 20

”

0.25

”

. Contact an Eaton

service representative for a replacement filter. To remove the filter:

Remove one top screw and two bottom screws securing the FI-UPM front
panel (refer to the

Power Xpert 9395 Field Installed UPM Mechanical

Installation Manual

listed in paragraph 1.8 on page 1-10.). Lift the panel

straight up to remove it from the panel hanger bracket at the top of the
cabinet.

Pull the foam filter over the screw heads on the cabinet mounted studs and
remove the filter from the cabinet.

Содержание Power Xpert Plus 1



































































































































































































Результаты поиска

Содержание Power Xpert Plus 1

Отзывы:

Похожие инструкции для Power Xpert Plus 1

Бренды по названию

Популярные бренды

Eaton Power Xpert Plus 1, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Power Xpert Plus 1

Отзывы:

Похожие инструкции для Power Xpert Plus 1

Бренды по названию

Популярные бренды