Eaton Power Xpert Plus 1 Скачать руководство пользователя страница 169

Страница: 169 / 194

UPS OPERATING INSTRUCTIONS

Power Xpert

9395 UPS (450–550 kVA) Installation and Operation Manual

164201701 Rev 3

www.eaton.com/powerquality

7-41

11.

Verify External Communications Failure alarm has cleared and no other alarms
are active on the online UPSs.

12.

On the System Status screen, select the

UPS

command.

13.

Press the

CONTROLS

pushbutton on the System Status menu bar. The UPS

Control Command screen is displayed.

14.

On the UPS Control Command screen, select

GO TO ONLINE

15.

Press the

SELECT

pushbutton on the UPS Command menu bar.

NOTE

If the UPS is starting on a bus with other online paralleled UPSs, the UPS will not go to bypass

during startup. The UPS will start, sync to the other UPSs online, and go online.

16.

Verify the following messages display sequentially on the UPS status line:

DC STARTING, CHARGER OFF
INVERTER STARTING
INVERTER SYNCING
ONLINE, CHARGER ON

The rectifier and inverter turn on. The inverter continues to ramp to full voltage.

Once the inverter reaches full voltage, the UPS output contactor (K3) closes.
Power is now supplied to the critical load in Online mode along with the other
UPSs online. It takes approximately one minute for the UPS to achieve Online
mode.

The

ONLINE

status indicator is illuminated. The UPS status indicates

ONLINE

. The

UPM status indicates

ONLINE, CHARGER ON

7.4.23

UPS and Critical Load Shutdown

To perform maintenance or service on the critical load, shut down power to the load:

Turn off all equipment that is being powered by the distributed bypass system.

Transfer the UPSs to bypass by performing the procedure in paragraph 7.4.5.

Perform the LOAD OFF procedure in paragraph 7.4.25.

The input, output, battery, and bypass backfeed contactors open, and the power
module is turned off.

Power is present inside the UPS cabinet until the upstream input feeder circuit breaker is opened.

If the UPSs contain input breakers (CB1), open all UPS input breakers.

Open the input and bypass feeder circuit breakers on all UPSs .

Содержание Power Xpert Plus 1



































































































































































































Результаты поиска

Содержание Power Xpert Plus 1

Отзывы:

Похожие инструкции для Power Xpert Plus 1

Бренды по названию

Популярные бренды

Eaton Power Xpert Plus 1, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Power Xpert Plus 1

Отзывы:

Похожие инструкции для Power Xpert Plus 1

Бренды по названию

Популярные бренды