Dynapac CC950 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 143

background image

Maintenance - 200 / 600 / 1400 / 1800 h

4812164101_A.pdf

2022-02-09

Maintenance - 200 / 600 / 1400 / 1800 h

Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.

Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.

Check that the engine cover is fully open before
carrying out work underneath it.

Check that the engine cover is fully open before
carrying out work underneath it.

Forward / Reverse controls and joints
- Check and lubrication

Fig. Forward/reverse lever
1. Friction nut

1

Unscrew the protective plate. Check the friction on the
forward/reverse lever. The friction nut (1) should be
applied with sufficient pressure to keep the
forward/reverse lever in the set position during
operation.

If the lever gets stiff after prolonged use, lubricate the
lever at the bearing bushings and at the cable with a
few drops of oil at each place.

3

2

Fig. Engine compartment
1. F/R lever cable
2. Heat cover
3. Air filter

1

If the forward/reverse lever still is stiff after the above
adjustments, lubricate the other end of the control
cable with a few drops of oil. The cable is located on
the top of the propulsion pump.

97

«
...
105
106
107
108
109
...
»

Содержание CC950
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC950

Бренд: UnionSpecial Страницы: 56

Бренд: TAIKO Audio Страницы: 24

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: Harris Страницы: 21

Бренд: Masalta Страницы: 13

Бренд: Gomaco Страницы: 30

Бренд: Panduit Страницы: 4

Бренд: ZAMST Страницы: 14

Бренд: Elliott Страницы: 46

Бренд: KUHN Страницы: 44

BoilerMag XT Series

Бренд: Spear & Jackson Страницы: 8

Бренд: MAHA Страницы: 138

Бренд: Delfield Страницы: 24

Бренд: Glow Bricks Страницы: 9

Бренд: KYORITSU Страницы: 16

Promarks TM-1000

Бренд: CM Страницы: 8

Бренд: XanLite Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды