Dynapac CC950 Скачать руководство пользователя страница 112

Страница: 112 / 143

Maintenance - 400 / 800 / 1200 / 1600 h

4812164101_A.pdf

2022-02-09

Water seperator in fuel tank - Clean

Switch off the engine and remove the key.

Use caution. Use the following protective
equipment:

Protective gloves

Taken out cleaning operation of water seperator in fuel
tank every 400 hours.

Refer to the engine manual for detailed
instructions.

Forward / Reverse controls and joints
- Check and lubrication

Fig. Forward/reverse lever
1. Friction nut

Unscrew the protective plate. Check the friction on the
forward/reverse lever. The friction nut (1) should be
applied with sufficient pressure to keep the
forward/reverse lever in the set position during
operation.

If the lever gets stiff after prolonged use, lubricate the
lever at the bearing bushings and at the cable with a
few drops of oil at each place.

102

Содержание CC950
















































































































































Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды

Dynapac CC950, Инструкция по эксплуатации

Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды