Dynapac CC950 Скачать руководство пользователя страница 129

Страница: 129 / 143

Maintenance - 1000h

4812164101_A.pdf

2022-02-09

Valve gasket - Change

Be sure the reinstall the detached safety shield
after maintenance or checking.

Use caution. Use the following protective
equipment:

Protective gloves

Refer to the engine manual for detailed
instructions.

Belt tension on the hydraulic vibration and
steering pump drive belt - Check

Fig. Engine compartment
1. Screw
2. Screw

If the hydraulic pump drive belt can be pressed in 5-6
mm between the pulleys with a force of 50 Nm, then
the belt is correctly tensioned.

Do as follows to tension the belt:

- Undo the screws (1) and (2).

- Press over the hydraulic pump so that the belt
tensions to the specified extent.

- Tighten screw (1) and then screw (2).

- Check that the belt still has the correct tension after
tightening.

Replace the belt when necessary, or after 2000 h.

119

Содержание CC950
















































































































































Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды

Dynapac CC950, Инструкция по эксплуатации

Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды