Dynapac CC950 Скачать руководство пользователя страница 3

Страница: 3 / 143

2000h-

Maintenance

4812164101_A.pdf

2022-02-09

Table of Contents

Introduction .............................................................................................................................. 1

Signal symbols and meaning ...................................................................... 1

The machine ............................................................................................... 1

Intended use ............................................................................................... 1

Safety information ....................................................................................... 1

General ....................................................................................................... 2

Signal symbols and meaning ...................................................................... 3

Safety - General instructions.................................................................................................... 5

Safety - when operating ........................................................................................................... 7

Seated position ........................................................................................... 7

Work driving ................................................................................................ 7

Driving near edges ...................................................................................... 8

Safety information ....................................................................................... 8

Special instructions ................................................................................................................ 11

Standard lubricants and other recommended oils and fluids .................... 11

Higher ambient temperatures, above +40°C (104°F)................................ 11

Lower ambient temperature - Freeze risk ................................................. 11

Temperatures............................................................................................ 11

High pressure cleaning ............................................................................. 12

Fire fighting ............................................................................................... 12

Fire extinguisher........................................................................................ 12

Roll Over Protective Structure (ROPS) ..................................................... 12

Battery handling ........................................................................................ 13

Jump starting............................................................................................. 13

Technical specifications ......................................................................................................... 15

Vibrations - Operator station ..................................................................... 15

Noise level................................................................................................. 15

Slopes ....................................................................................................... 15

Dimensions, side view............................................................................... 16

Dimensions, top view ................................................................................ 17

Содержание CC950
















































































































































Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды

Dynapac CC950, Инструкция по эксплуатации

Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды