Dynapac CC950 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 143

background image

Operation

4812164101_A.pdf

2022-02-09

Parking

Chocking the drums

Fig. Set-up
1. Chocks

1

Never leave the operator platform without
activating the parking brake.

Never leave the operator platform without
activating the parking brake.

Make sure that the roller is parked in a safe place
with respect to other road users. Chock the drums
if the roller is parked on sloping ground.

Make sure that the roller is parked in a safe place
with respect to other road users. Chock the drums
if the roller is parked on sloping ground.

Keep in mind that there is a risk of freezing during
the winter. Drain the water tanks and water lines.
Fill antifreeze in the engine cooling system. Also
see maintenance instructions.

Keep in mind that there is a risk of freezing during
the winter. Drain the water tanks and water lines.
Fill antifreeze in the engine cooling system. Also
see maintenance instructions.

Before using the roller again, make sure that the
engine is switched off and the parking brake is
activated. The brake chocks can then be removed.

Before using the roller again, make sure that the
engine is switched off and the parking brake is
activated. The brake chocks can then be removed.

Battery disconnector

1

Fig. Engine compartment
1. Battery disconnector

Before leaving the roller at the end of the shift, switch
off the battery disconnector (1) and remove the key.

This will prevent battery discharging and will also
make it difficult for unauthorized persons to start and
operate the machine. Lock also the engine cover.

49

«
...
57
58
59
60
61
...
»

Содержание CC950
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC950

Бренд: Qingdao H.Y Страницы: 6

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Nektar Страницы: 3

Бренд: Youkey Страницы: 86

Бренд: Wacker Neuson Страницы: 62

Бренд: Taurus Страницы: 24

Бренд: JBL Страницы: 38

Бренд: JBSYSTEMS Light Страницы: 32

Бренд: Parkside Страницы: 58

LSP400 LED Series

Бренд: WE-EF Страницы: 6

Бренд: uniprox Страницы: 3

Бренд: Aspect Medical Systems Страницы: 104

Бренд: Hupfer Страницы: 153

Бренд: Veit Brisay Страницы: 18

Бренд: Costan Страницы: 154

Dual SD/HD Video Delay VLD-1002-MD

Бренд: Algolith Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды