Dynapac CC950 Скачать руководство пользователя страница 127

Страница: 127 / 143

Maintenance - 1000h

4812164101_A.pdf

2022-02-09

Hydraulic fluid filter - Change

Fig. Engine compartment, left side
1. Hydraulic fluid filter

Remove the filter (1) and deliver to special
waste handling. This is a single-use filter and
cannot be cleaned.

Thoroughly clean the filter holder sealing surface.

Apply a thin coat of fresh hydraulic fluid to the rubber
gasket on the new filter.

Screw the filter on by hand, firstly until the filter gasket
makes contact with the filter base. Then rotate a
further ½ turn.

Start the engine and check that the filter does not leak.

Do not over-tighten. The seal can be damaged.

Dispose of the old filter carefully.

Steering joint - Check

Fig. Steering joint

Inspect the steering joint to detect any
damage or cracks.

Check and tighten any loose bolts.

Check also for any stiffness and play in the steering
joint. Rectify if necessary.

117

Содержание CC950
















































































































































Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды

Dynapac CC950, Инструкция по эксплуатации

Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды