Dynapac CC950 Скачать руководство пользователя страница 12

Страница: 12 / 143

Introduction

4812164101_A.pdf

2022-02-09

Replace immediately the instruction manuals if
lost, damaged or unreadable.

Ensure good ventilation (extraction of air by fan)
where the engine is run indoors.

CALIFORNIA

Decal and location of decal shown in section
Machine description.

Proposition 65

General

This manual contains instructions for machine
operation and maintenance.

The machine must be correctly maintained for
maximal performance.

The machine should be kept clean so that any
leakages, loose bolts and loose connections are
discovered at as early a point in time as possible.

Do not spray with high-pressure cleaner directly onto
gaskets and bearing spacings in steering hitch and
drum, and electronics.

Inspect the machine every day, before starting.
Inspect the entire machine so that any leakages or
other faults are detected.

Check the ground under the machine. Leakages are
more easily detected on the ground than on the
machine itself.

Содержание CC950
















































































































































Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды

Dynapac CC950, Инструкция по эксплуатации

Результаты поиска

Содержание CC950

Отзывы:

Похожие инструкции для CC950

Бренды по названию

Популярные бренды