Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 86

Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 70

70

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Appendix B

Appendix B – MANET recessed pull grips

Follow these instructions in addition to the Installation
and Maintenance Instructions in order to avoid damage
of product or property and injury to persons.

NOTICE

All users have to be informed about relevant
points referenced in these safety-related
instructions and the Installation and
Maintenance Instructions.

B.1.1 General information.

1. dormakaba recommends using TSG-H (heat soaked

toughened safety glass) to DIN EN 12150-1).

2. dormakaba glass fittings are not suitable for

applications in rooms where chemicals (e.g. chlorine)
are used, such as in indoor swimming pools, saunas,
or salt water pools.

3. Never move sliding glass panels faster than walking

speed and always stop the door manually before it
reaches the end position.

B.1.2 Mounting

1. Only properly qualified and specially trained staff

are authorized to mount dormakaba glass fittings.

2. Never use glass with conchoidal fractures and/or

damaged edges.

3. Due to crushing hazards, among others in the area

of the secondary closing edge, and possible injury
caused by the breakage of glass during mounting,
corresponding protective clothing (especially gloves
and protective goggles) are required.

4. Before mounting the glass fitting, clean clamping

area with fat solvent (standard commercial cleaning
agent).

5. Never use clamping shoes on structured glass

surfaces (except on satined glass) or glass of heavily
varying thickness unless used with a corresponding
leveling layer.

6. Never use clamping shoes on self-cleaning coatings.

7. When adjusting glass elements, always maintain the

required clearance for the respective fitting.

Adjust clearance so that the glass does not touch

hard components such as glass, metal or concrete.

8. Make sure not to use excessive force when installing

the glass (avoid local stress resulting from very tight
screws).

B.1.3 Maintenance

1. Check fittings at regular intervals for proper

positioning and smooth running.

2. Check door for correct adjustment.

3. Highly used door systems require inspection by

properly qualified staff (specialized companies or
installation firms).

4. Immediately replace damaged glass elements (no

glass flaking and/or conchoidal fractures)!

5. Only use suitable cleaning and care products to

clean the surfaces.

B.1 Safety-related information for the mounting and use of dormakaba

glass fittings

«
...
68
69
70
71
72
...
»

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов