manualshive.com logo in svg

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 35 / 86

Поделиться
Скачать
Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 35

35

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Maintenance Manual

Chapter 5

5.6 Safety 

functions

Static forces in Low-Energy mode.

The system does not exceed a value of 15 lbf [67 N] 
during opening and closing cycles.

Opening cycle

As soon as the door hits an obstacle during an opening 
cycle, it will immediately stop and remain in its position 
for 3 seconds. Then the operator will try to continue the 
opening cycle. 
If the door hits the obstacle three times during an 
opening cycle, it will close. 

Closing cycle

When the door panel hits an obstacle while closing, it 
will immediately stop and perform an opening cycle.

5.7 Safety sensors

Sensors can be installed to detect obstacles. An 
automatic sensor test can be activated or deactivated 
via the DIP switches located inside the operator.

Opening cycle.

The door will stop immediately when the sensor detects 
an obstacle during an opening cycle and will continue 
the cycle as soon as the object has been removed. In 
case the obstacle has not been removed, the door will 
close on completion of the adjusted hold-open time. 

Closing cycle.

The door will stop immediately and reverse when the 
sensor detects an obstacle during the closing cycle. 

Door in closed position.

This function is not activated while the door is in the 
closed position (then the sensor is deactivated).

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов