Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 86

Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 31

31

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 3

3 Important installation instructions

NOTICE

All installations and service should only be
performed by training or authorized persons.

3.1 Warning - To reduce the risk of injury or death:

1. Carefully read and follow all installation instructions.

2. This unit should only be installed in a rough opening

capable of providing proper structural support.

3. Always disconnect the 115Vac power supply before

servicing.

4. To install and adjust the door for proper and safe

operation, the installer must carefully read this
instruction manual before proceeding, then follow
the instructions.

5. The door is designed to be installed only by trained

and knowledgeable installers.

6. The installation technician should be experienced in

the installation of automatic door entrances. The
technician should know all local code requirements
and be familiar with the current ANSI/BHMA
standards:

• A156.10 Standard for Power Operated Doors

• A156.19 Standard for Power Assist and Low Energy

Power Operated Swing Doors.

• A156.38 Standard for Low Energy Power Operated

Sliding and Folding Doors.

7. After installation, the door must be adjusted to

conform with dormakaba recommendations and all
code requirements. Carefully study the requirements
in these instructions.

8. After installation and adjustment, the installer's

final responsibility is to properly instruct the owner in
the safe use of the door. The owner must also be
presented with this manual.

9. Each step of the installation, adjustment and

instructions are important for the proper and safe
use of the door being installed. If there are any
questions about any items contained in these
instructions, call the local dormakaba distributor for
assistance.

10. Save these instructions for future reference.

3.2 Compliance with Safety Standards.

The door system was designed to the latest operating
and safety standards. In order to ensure the continued
safe operation of the door, it is important that:
• The door system be maintained in compliance with

the standards of the industry, ANSI/BHMA.

• Proper decals and labels be applied, per ANSI/BHMA

standards, and maintained on the door. If decals are
removed, or cannot be read, request replacements
when calling for service.

«
...
29
30
31
32
33
...
»

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов