manualshive.com logo in svg

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 52 / 86

Поделиться
Скачать
Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 52

52

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 9

Fig. 9.1.14  Panel installation

Fig. 9.1.15  Door panel alignment for level

.250” [6

 mm]

9.1.16  Align door panel for level.

1.  Using the adjustment nuts, align door panel so that it 

is level.

NOTICE

The distance between the bottom edge of the 
door panel and the floor should be 1/4" [6.35 mm]. 
The distance must not exceed 5/16" [7.94 mm]

9.1.15 Install panel.

1.  Insert panel into door panel suspension.

2.  Align panel so that it is parallel to wall and secure it 

with fasteners.

Fig. 9.1.13  Panel installation

9.1.14  Place door panel inside door frame.

1.  Move end stop to end of channel.

CAUTION

End stop must not fall out of operator.

2.  Place door inside door frame.
•  As door panel is wider than the doorway, the panel 

will have to be tilted.

TIPS AND RECOMMENDATIONS

As it will be difficult to manually lift the door 
with in-wall mounting, wooden wedges should 
be used to facilitate lifting the door panel.

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов