Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 86

Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 59

59

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 14

14 Operating instructions

14.1 Opening the door in AUTOMATIC function.

When the system is delivered ,the CS 80 MAGNEO is
adjusted to AUTOMATIC function.
Depending on the installed accessories, the door can be
opened in different ways.

14.1.1 Push & Go.

1. As soon as the door is manually moved into the opening

direction by approximately 4" [10 mm], the operator
automatically moves the door panel further in the
opening direction.

2. The door closes automatically.

14.1.2 Pushbutton

Following the activation of the pushbutton (e.g. wall
mounted pushbutton or radio transmitter) the operator
opens, then closes the door.

14.1.3 Sensors

When presence sensors are connected,the door opens
automatically as soon as a persons approaches the
door system.
The door closes automatically.

14.2 Permanent Open by double-click.

1. To activate this function, set DIP switches 4 and 5 to

the ON position.

2. Once activated:

• To open the door, double-click the pushbutton.

• To close the door, double-click the pushbutton again.

14.3 Opening/Closing by pushbutton (alternate action).

1. To activate this function, set DIP switches 4, 5 and

to the ON position.

2. Once activated:

1. To open the door, push the button or manually move

the door.

2. When the button is pushed a second time, or the

door is manually moved, the door will close.

8

7

6

5

4

3

2

1

ON

8

7

6

5

4

3

2

1

ON

14.4 Express function.

The door can be moved manually into its driving
direction without extra resistance.
• When maximum speed is exceeded, the operational

resistance will increase in line with the speed by
which it is exceeded.

• As soon as the user releases the door panel, the

operator will gradually slow the panel down to
maximum speed.

• This function is activated during all opening and

closing cycles.

14.5 In

the event of power failure.

In the event of power failure, the door can be manually
opened and closed.

NOTICE

In the case of power failure, the system does
not brake the door panel, which means the
user has to manually move (hold) the door
panel for the panel full travel distance.

As soon as the power returns, the operator will
automatically perform a positioning initialization.

NOTICE

During this position initialization,the door
movement range must be free of obstacles.

14.6 Adjustments.

WARNING

Use only the enclosed red screwdriver to
perform potentiometer adjustments.

14.6.1 Speed

adjustment.

The maximum speed depends on the weight of
the door panel.

The speed can be reduced by adjustment of
the speed potentiometer.

14.6.2 Hold-open

time

adjustment.

After reaching the open position, the door will
close automatically upon expiration to the
adjusted hold-open time.

The hold-open time can be adjusted from 5 to
30 seconds with the hold-open time
potentiometer.

«
...
57
58
59
60
61
...
»

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов