Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 40

Страница: 40 / 86

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 8

8 Installation instructions for on-wall

mounting

8.1.1 Mounting procedure.

If there is a door frame, the angle bracket must be
shimmed with a shim plate (Para. 8.1.7).

1. Auxiliary lines for positioning purposes (Para. 8.1.2).

2.1 Installation without shim plate (Para. 8.1.5).

2.2 Installation with shim plate (Para 8.1.7).

8.1.2 Positioning guide.

1. For installation without shim plate mark the center

of passage on the wall.

2. For installation with shim plate mark center of

passage on the wall.

• Refer to Table 8.1.1 for required

dimension for the

operator reference line.

• L corresponds to operator length.

3. Mark the reference line (Fig. 8.1.3).
• Always mark the reference line on the side of the

main closing edge (Fig. 8.1.4).

34.4" [875]

39.4" [1000]

44.3" [1125]

22.7" [575]

27.6" [700]

32.5" [825]

68.9" [1750]

78.7" [2000]

88.6" [2250]

17.2" [437.5]

19.7" [500]

22.1" 562.5]

TIPS AND RECOMMENDATIONS

In case the door panel is not positioned in the
center of the passage, the bracket or shim
plate must be shifted by the desired dimension.

Fig. 8.1.1 Glass door panels with MANET single-point

attachment

Main closing edge

renc

line

Fig. 8.1.3 Reference line

Table 8.1.1

Max. passage width, C, L and M dimensions

Fig. 8.1.2 Door panel information

Main closing edge

Secondary closing edge

Fig. 8.1.4 Main closing edge

8.1 Mounting

procedure

Edge grinded glass

CENTERED

2.5" [63 mm]

2.2" [55 mm]

Min. 2.76"

Min 70 mm]

Glass heigh

= H - 5” [

12 mm]

Ø1.03” [Ø26 mm] hole
CSink Ø1.26” [Ø32 mm] x 90⁰

“Closed” side

Glass width

Drill hole for
recessed door grip
(optional)

Ø0.1.97” [Ø50 mm] hole
CSink Ø2.05” [Ø52 mm] x 90⁰

90⁰

Min. 0

.2”

Min. 5 mm

”

62 mm

Max.
.31”
8 mm

.250”
6 mm

Finished floor

Angle floor guide rail
compl.

Maximum passage width.

Содержание CS 80 MAGNEO























































































Результаты поиска

Содержание CS 80 MAGNEO

Отзывы:

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 40 / 86

Результаты поиска

Содержание CS 80 MAGNEO

Отзывы: