manualshive.com logo in svg

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 63 / 86

Поделиться
Скачать
Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 63

63

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 16

Malfunction

Possible causes

Remedy

The red LED blinks 3 times at 
regular intervals.

The power mode switch of the door 
has been switched to another position.

Switch power switch off and on.

The red LED blinks 4 times at 
regular intervals.

Testable safety sensors are defective.

Check and replace safety sensors if 
required.

Damaged sensor cable.

Check and replace cables if required.

DIP switches 1 and 3 are not set 
correctly.

Check DIP switch settings and 
readjust if required.

The red LED blinks 5 times at 
regular intervals.

Incremental encoder or cable of 
incremental encoder is defective.

Switch mains switch off and on.
Replace operator.

The opening width is incorrectly 
adjusted.

Readjust opening width (end stops).

Start learning cycle (Chapter 13).

The red LED blinks 6 times at 
regular intervals.

There is an obstacle within the door's 
movement range.

Remove obstacles from movement 
range.

The opening width is incorrectly 
adjusted.

Readjust opening width (end stops).

Start learning cycle (Chapter 13).

The red LED blinks 10 times at 
regular intervals.

Stator or cable of stator is defective.

Switch power switch off and on.
Replace operator.

Short circuit at terminal connection.

1.  Remove the short circuit.
2.  Switch power switch off and on.

Humming noise while door is in 
end position.

Inappropriate end position of door 
panel.

Shift end stop by at least 1/16" [2 mm].

Start learning cycle (Chapter 13).

The door panel vibrates when 
moving.

The guide mechanism is under tension.

Readjust door panel connection and 
the floor guide if required. Turn the 
nuts several times in order to fix the 
door panels.

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов