Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 48

Страница: 48 / 86

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 9

9 Installation instructions – in-wall mounting

9.1 Installation

instructions

9.1.1 Minimum recess for CS 80 MAGNEO operator.

The CS80 MAGNEO sliding door operator is also
suitable for an "invisible" in-wall mounting.

For this type of mounting, a recess with a minimum
width of 2" [50 mm] and a depth of 2.95" [75 mm] is
required.

A special door frame manufactured by BOSS can be
used. Contact dormakaba for additional details.

9.1.2 Installation dimensions.

NOTICE

Dimension X

• When using a Wooden door panel:
X = door panel 3" [78 mm].

• When using a glass clamping rail:
X = door panel 4 1/2" [114 mm].

• When using dormakaba MANET single

point fixings:

X = door panel 2 29/32" [74 mm].

2" [50 mm]

]

Fig. 9.1.1

Minimum recess, in-wall mounting

Table 9.1.1

Installation dimensions

68.9" [1750 mm]

78.7" [2000 mm]

88.6" [2250 mm]

17.2" [437.5 mm]

19.7" [500 mm]

22.1" 562.5 mm]

73.6" min.

[1750 mm] min.

83.5" min.

[2120 mm] min.

73.6" min.

[2370 mm] min.

22.7" [575 mm]

27.6" [700 mm]

32.5" [825 mm]

A = minimum L + 4.72” [120 mm]

2” min.

[50 mm] min.

2.75” min.

[70 mm] min.

Bottom edge of header

.75” min.

0 mm] min.

Centered

“Closed” position

.50” .

[63.5 mm]

Dimension

must be

measured at the highest point
of floor within movement
range of door system,

• Dimension

: Operator length.

• Dimension

: Distance from center of passage area.

to side of operator where connections are located.

• Dimension

: Minimum width between frames.

• Dimension

: Height of top of operator from floor.

Fig. 9.1.2 Door system installation dimensions

CAUTION

Holes for cables must be sufficiently large
and must not have sharp edges.

TIPS AND
RECOMMENDATIONS

The wall must not be
closed before the
system has been
installed.

Содержание CS 80 MAGNEO























































































Результаты поиска

Содержание CS 80 MAGNEO

Отзывы:

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 48 / 86

Результаты поиска

Содержание CS 80 MAGNEO

Отзывы: