Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 86

Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 30

30

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 8

2.1 General

information

The door must be installed and adjusted properly to
ensure its proper operation and safe use.

To install and adjust the door for proper use and safe
operation, the installer must carefully read this
instruction book before proceeding, then follow its
instructions.

The door is designed to be installed only by trained and
knowledgeable installers.
The installation technician should be experienced in the
installation of the automatic entrance product line.

After installation, the door must be adjusted to
conform to dormakaba recommendations and all code
requirements. Be sure to carefully study the
requirements in these instructions.

After installation and adjustment, the installer's final
responsibility is to properly instruct the owner in the
safe use of the door. The owner must also be presented
with the CS 80 MAGNEO Owner's Manual and to
carefully explain how to perform the daily safety check
list.

Each step of the installation, adjustment and
instructions are important for proper and safe use of
the door being installed. If there are any questions
about any items contained in these instructions, call the
local dormakaba distributor for assistance.

2 General information, required tools

2.2 Required

tools

• Tape

measure

• Spirit

level

• Pencil

• Electric

drill

• Masonry drill bit 01/4"

• Metal drill bits 01/8" and 05/16"

• Socket wrench [10 mm]

• Small flat head screwdriver for terminals on control

unit.

• Phillips screwdriver for countersunk screws of wall

connection.

• Allen (hex) key [4 mm]

• Combination wrench, sizes [10 mm and 13 mm]

• Long nosed pliers for wire connections to terminals.

• Adequate screws and wall anchors for the

structures, in case they are not made of brickwork or
concrete.

2.2.1 Additional tools for dormakaba MANET

attachment.

• Allen (hex) key, [3 mm and 5 mm]

«
...
28
29
30
31
32
...
»

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов