manualshive.com logo in svg

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 53 / 86

Поделиться
Скачать
Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 53

53

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 9

9.1.17 Secure end stop at desired door closed position.

1.  Loosen the end stop screws on the side where the 

connections are made.

2.  Move the door to the desired position.

3.  Move end stop next to the door panel and tighten the 

end stop fasteners.

NOTICE

The end stop may only be moved to the inside 
by a certain maximum dimension Y:

34.4" [875 mm] operator =>7.9" [200 mm].

39.4" [1000 mm] operator =>9.5" [250 mm].

48.2" [1125 mm] operator =>11.8" [300 mm].

Fig. 9.1.16  End stop final position

3.

3.

Y

4.

1.

Y

2.

9.1.18 Secure opposite end stop in door open position.

1.  Loosen opposite side end stop screws.

2.  Move door to desired open position.

3.  Move end stop next to door panel.

4.  Tighten end stop screws.

NOTICE

The end stop may only be moved to the outside 
by a maximum dimension (Y):

34.4" [875 mm] operator =>7.9" [200 mm].

39.4" [1000 mm] operator =>9.5" [250 mm].

48.2" [1125 mm] operator =>11.8" [300 mm].

3.

2.

1.

Y

4.

Y

Fig. 9.1.17  End stop final position

9.1.19  Door panel to wall maximum distance.

NOTICE

The distance between the door panel and wall 
must not exceed 5/16" [7.94 mm].

9.1.20 Connection of external accessories.

1.  Connect all external accessories except for safety 

sensors. Refer to cable channel instructions.

9.1.21  Continue with system commissioning.
                 Reference Chapter 13.

.3125" max.
[8 mm max.]

Fig. 9.1.18  Door panel to wall minimum distance

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов