Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 86

Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 3

3

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 8

1 Technical data and

MAGNEO configurations

1.1 Technical

data

Power supply

115 Vac ±10%, 50/60 Hz

Branch circuit
protection
(by others)

15 A

Cable type

14 AWG (Max. 12 AWG)

[Max. 3 x 1.5 mm

2

]

1.1.1 Power supply.

Standby mode

5.6 W

Automatic mode

Max. 60 W

1.1.2 Power consumption without external accessories.

Temperature range

0 - 104° F [0 - 40° C]

Operating noise of
operator

Max. 55 dB (A)

Door panel height

Max. 118"

[Max. 3000 mm]

Door panel weight

44lbs - 175lbs

[20 kg - 80 kg]

1.1.3 General information.

1.1.4 Weight of operator.

FCC 15.105 (a)

NOTE:

This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generated,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his/her expense.

1.1.5 Symbols used in these instructions.

WARNING

This symbol warns of hazards which could result
in personal injury or threat to health.

CAUTION

This symbol warns of a potentially unsafe
procedure or situation.

NOTICE

Draws attention to important information
presented in this document.

TIPS AND RECOMMENDATIONS

Clarifies instructions or other information
presented in this document.

Maximum

passage width

Operator

length

without cover

Weight of

operator

34.4"

[875 mm]

69.9"

[1750 mm]

18.8 lbs

[8.6 kg]

39.4"

[1000 mm]

78.7"

[2000 mm]

20.7 lbs

[9.4 kg]

44.3"

[1125 mm]

88.6"

[2250 mm]

22.4 lbs

[10.2 kg]

1.1.5 Cover page illustration.

Cover page documents the CS 80 MAGNEO
ON-WALL operator configurations.

Reference Paragraphs .2 through .13 for all CS 80
MAGNEO operator configurations.

«
1
2
3
4
5
...
»

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов