manualshive.com logo in svg

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 73 / 86

Поделиться
Скачать
Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 73

73

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Appendix C

Appendix C – Power Fail Locking

NOTICE

In conjunction with an electromechanical 
locking device, an external program switch is 
required.

C1.1 

When program switch set to "OFF", the 

 

 

operator closes and locks the door.

C1.2 

Whenever an opening pulse is triggered at the

 

 

"internal activator" (terminals 3 and 42), the 

 

 

locking device unlocks and the operator opens 

   the 

door.

C1.3 

On expiration of the adjusted hold open time,

 

 

 the operator closes and locks the door.

C.1 Functional 

description

WARNING

Safety instructions (                ) "Mounting 
instructions and instructions for use of 
operator" must be observed.

C.2 Mounting

NOTICE

Preparation of mounting: 
1) Determine"closed" position.

2) Mount drive unit.

3) Attach door panel and move door to 
"closed" position.

C2.1  Overview: Removing end stop attachment screws 

and end stop.

1.  Carefully pull out carrier until the attachment 

 screws of the "stop" are visible.

2.  Remove end stop screws; remove end stop.

Reference Para. C2.2 through C2.9 for step by step 
instructions.

C1.5 

An opening pulse at the "external activator" 

 

 

(terminals 3 and 41), has no effect while the

 

 

 program switch is set to "OFF".

 

 

These terminals are only activated while the 

 

 

program switch is set to "AUTOMATIC" mode

 

 

(reference operating instructions).

C1.6 

In the event of a power failure, the locking 

 

 

device unlocks so that users may manually open

   the 

door.

1.

3.

2.

Fig. C2.1  End stop attachment screw removal

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов