manualshive.com logo in svg

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 42 / 86

Поделиться
Скачать
Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 42

42

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 8

8.1.5  Mounting with angle bracket.

CAUTION

Before drilling any holes, make sure that there 
are no cables and/or pipes in the angle 
bracket installation location.

1.  Position angle bracket onto center line.
•  Insure that the bottom vertex of the triangle is 

located exactly on the center line (Fig. 8.1.6).

2.  Align angle bracket so that it is level.

3.  Secure angle bracket with screws (one screw per one 

oblong hole on each side).

CAUTION

When installing the angle bracket, use 
adequate wall plugs and screws depending on 
the prevailing structure.
•  The supplied screws and wall plugs are 

suitable for concrete and brickwork.

4.  Recheck angle bracket for exact positioning.

5.  Drill additional holes through the drill holes in the 

angle bracket and secure the bracket with a 
minimum of 12 screws (Fig. 8.1.7).

8.1.6 Uneven walls.

1.  In case of uneven walls the bracket must be 

shimmed so that it does not bend.

2.  Use the enclosed shims (in different sizes) for this 

purpose (Fig. 8.1.8).

Fig. 8.1.6  Mounting bracket positioned onto centerline

Fig. 8.1.7  Angle bracket secured with minimum of 12 

screws

Fig. 8.1.8 Shimming mounting bracket

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов